Ecosoft Professional MO36000 4″ reverse osmosis system

DescriptionTechnical informationParameterRated capacity 1500 L/h Rated capacity 36000 L/d Recovery up to 75 % Inlet water TDS 3000 ppm Membranes (pcs/type) 6/40×40 Inlet water pressure 2…4 bar Operating pressure 8…12 bar Maximum pressure 14 bar Service feed flow 2000–2500 L/h Forward flush feed flow 4200 L/h Water consumption for forward flush 70 L Inlet water temperature 5…30 °C Online access no Controller menu languages EN Power supply 1 × 220–230 V Frequency 50 Hz Rated power 1.9 kW System dimensions (H × W × D) 1490 × 870 × 580 mm System weight 130 kg Permeate flow* 27 LPM Concentrate flow* 9 LPM Recycle flow* 24 LPM Operating pressure* 10.0 barSystem ComponentsPump: Grundfos® CM 3-14, high-energy efficiency (IE4, A ), low noise and vibration, AISI 304 – 1 pcs Membrane vessel: 300 psi – 6 pcs Electrical panel and controller: Ecosoft OC5000 Conductivity cell (permeate): yes Sediment prefilter: BB20 – 1 pcs Sediment filter: PP melt-blown 4.5″ × 20″, 5 µm – 1 pcs Frame: Steel, powder-coated – 1 pcs Inlet solenoid valve: Danfoss – 1 pcs Forward flush solenoid valve: Danfoss – 1 pcs Float switch: 1 pcs Pressure switch after sediment filter: adjustable Pressure switch on permeate line: adjustable Permeate rotameter: 5–35 LPM, non-adjustable Concentrate rotameter: 5–35 LPM, adjustable Permeate recycle: 10–50 LPM, adjustable Pressure gauge inlet before sediment filter: 10 bar Pressure gauge after sediment filter: 10 bar Operating pressure gauge: 16 bar Connection feed water: G 1 Connection permeate: G 1 Connection concentrate: G 1 Connection ports for dosing pump: G ½ Connection ports for permeate flush kit: G 1 Connection ports for raw water blending kit: G ⅜Source Water RequirementsMax. inlet water TDS (Total dissolved salts) 3000 ppm Hardness (without antiscalant) 150 ppm CaCO₃ Hardness (with antiscalant) 15000 ppm CaCO₃ Silica 20 mg/L SiO₂ Residual chlorine 0.1 mg/L Chemical oxygen demand 5 mg/L O₂ Iron 0.1 mg/L Manganese 0.05 mg/L Hydrogen sulfide none Chlorides 500 mg/LServiceTo ensure maximum efficiency of the Ecosoft reverse osmosis system, regular replacement of filter elements is required. Proper maintenance guarantees high water quality and extends the service life of your system.Cartridge replacement schedule:Ecosoft PP melt-blown sediment filter, 4.5″ × 20″, 5 µm – replace every 4 months, or if the pressure drop reaches 0.5 bar Membrane element – replace or clean every 6 months if productivity decreases by more than 15–20%, water quality worsens by 15–20%, or pressure drop increases by 15–20% You can replace cartridges and membrane elements yourself, but for best results we recommend contacting an authorized service center.If you decide to carry out the replacement yourself, follow the instructions below:⚠️ Use sterile rubber gloves when handling membrane elements⚠️ If high microbiological purity is required, disinfect the reverse osmosis system and the permeate tank before installing the membraneMembrane holder cap 1 – Screws, 2 – Locking half-rings, 3 – End cap, 4 – Sealing ring, 5 – Sealing ring for the end cap.Remove the membrane element(s) from the factory packaging. To replace the old element with a new one, disconnect the pipelines and remove the membrane holder(s) from the frame.⚠️ Pay special attention to the sealing ring of the end cap (5). If the seal is missing, permeate and concentrate streams may mix.After removing the end cap, install the membrane element in the direction of the arrow marked on the membrane holder (from the inlet water side). The membrane element must be inserted into the holder with its sealing ring aligned with the inlet connection of the holder head.After installation, secure the holder head with screws and locking elements to the holder body, then reconnect the pipelines for feed water, concentrate discharge, and permeate outlet on the membrane holder. Fix the membrane holder to the reverse osmosis system frame.During the first system startup, the initial portion of permeate must be discharged to the sewer, with a minimum discharge time of 15 minutes.�� When installing the membrane, pay attention to the direction of the arrow on the membrane holder.�� If necessary, use glycerin as a lubricant. Video DownloadsTechnical data sheet Ecosoft МО36000Instruction manual Ecosoft RO System MiniComparison table